• Home

  • Products

    • Local Shipping
    • Tasmota
    • ESPHome
    • WLED
    • Homekit
    • Home Bridge
  • Forum

  • About Shipping

  • Contact Us

  • 更多

    Use tab to navigate through the menu items.
    0
    כדי לראות את זה בפעילות, יש לעבור לאתר הפעיל שלך.
    • קטגוריות
    • כל הפוסטים
    • הפוסטים שלי
    Joerie Rave
    28 בנוב׳ 2020

    Flash Homekit version switch with Tasmota?

    ב- Wall Switch

    I try to find information about flashing the 'SW11-2EU

    EU Touch Switch 2 gang' (with Homekit firmware pre-installed) to Tasmota.


    The Homekit version of this switch won't connect to Home Assistant (Homekit connect integration) with code 123-45-678. What makes it useless unless i can flash Tasmota that does connect to HA.


    Can someone point me in the right direction?

    6 תגובות
    0
    6 תגובות

    שיתוף המחשבות שלךצריך להירשם כדי להשאיר תגובה.

    J
    Jayson Priest
    Jayson Priest
    17 באוג׳ 2021

    Hi, I just thought I would add to this my experience with flashing the homekit version to latest HAA version. The process was simple, use the latest HAA Bin file, flash it using the update via the interface at 192.168.4.1. Once flash is complete join the new broadcast wifi on HAA-xxxx add your wifi details and the following JSON (for a 4 gang version). I have used a grouping in this case: {"c":{"b":[{"g":0,"t":5}]},"a":[

    {"0":{"r":[{"g":13}]},"1":{"r":[{"g":13,"v":1}]},"b":[{"g":12}],

    "es":[

    {"0":{"r":[{"g":14}]},"1":{"r":[{"g":14,"v":1}]},"b":[{"g":16}]},

    {"0":{"r":[{"g":4}]},"1":{"r":[{"g":4,"v":1}]},"b":[{"g":3}]},

    {"0":{"r":[{"g":15}]},"1":{"r":[{"g":15,"v":1}]},"b":[{"g":5}]}]}]}

    לייק

    N
    Neil Heuer
    Neil Heuer
    31 ביולי 2021

    It can be done. When the switch is in AP mode you have to go to 192.168.4.1/update then you can upload your own bin file. On my 4 gang it just started clicking so you have to do the device recovery after that.


    Procedure~

    1. Cut power from the device completely for 30 seconds

    2. Power the device on and off six times with intervals lower than 10 seconds and leave it on after seventh time

    3. Fast power cycle device recovery should activate and the device should be reset to firmware defaults


    לייק

    daan
    04 ביוני 2021

    When you upgrade the firmware to version 0.6 you will get a new code, that code does work with Home Assistant.

    לייק

    daan
    05 באפר׳ 2021

    Same issue here!

    לייק

    J
    Joerie Rave
    Joerie Rave
    18 בינו׳ 2021

    No, i didn't. :( Did you?

    לייק

    conrad
    30 בדצמ׳ 2020

    Hi. Did you find a way to flash? I have an EU Plug with homekit pre-installed and want it to flash with standard Tasmota.

    לייק
    6 תגובות
    פוסטים דומים
    • Is it possible to flash to tasmota from homekit, without open case, via web interface?
    • Tasmota dimmer switch?
    • How to change Tasmota to Homekit?

    ©2020 by athom.