I've installed the 2 Gang Wall Switch in our kitchen. One switch is controlling normal spotlights in the ceiling, the other switch is controlling a LED line.
Everything worked well so far, BUT when the switch for the LED line is off, the light blinks/flashes every 2 seconds. I've checked the settings and tried different things here but the flashing doesn't stop.
Any idea? Log below. Thank you!
15 23:26:43 Relay 2 . . . ON
15 23:26:44 Relay 1 . . . OFF
15 23:26:45 Relay 1 . . . ON
15 23:27:16 Relay 1 . . . OFF
15 23:27:26 saveConfig . . . EEPROM OK Len: 250 Crc: 1478
15 23:27:30 Relay 1 . . . ON
15 23:27:32 Relay 1 . . . OFF
15 23:27:36 Relay 2 . . . OFF
15 23:27:39 Relay 1 . . . ON
15 23:27:40 saveConfig . . . EEPROM OK Len: 250 Crc: 56196
15 23:27:43 Relay 1 . . . OFF
15 23:27:49 Relay 1 . . . ON
15 23:27:51 Relay 1 . . . OFF
15 23:27:53 saveConfig . . . EEPROM OK Len: 248 Crc: 64845
15 23:27:57 Relay 1 . . . ON
15 23:27:58 Relay 2 . . . ON
15 23:27:59 Relay 2 . . . OFF
15 23:28:07 saveConfig . . . EEPROM OK Len: 250 Crc: 56196
15 23:28:14 Button 2 . . . SingleClick
15 23:28:14 Relay 2 . . . ON
15 23:28:16 Button 1 . . . SingleClick
15 23:28:16 Relay 1 . . . OFF
15 23:28:23 Button 1 . . . SingleClick
15 23:28:23 Relay 1 . . . ON
15 23:28:24 saveConfig . . . EEPROM OK Len: 249 Crc: 22408
15 23:36:49 Relay 1 . . . OFF
15 23:36:59 saveConfig . . . EEPROM OK Len: 250 Crc: 1478
15 23:37:02 Relay 1 . . . ON
15 23:37:06 saveConfig . . . EEPROM OK Len: 248 Crc: 25923
15 23:37:09 Relay 1 . . . OFF
15 23:37:15 Relay 1 . . . ON
15 23:37:17 saveConfig . . . EEPROM OK Len: 250 Crc: 60711
15 23:37:20 Relay 1 . . . OFF
15 23:37:30 saveConfig . . . EEPROM OK Len: 250 Crc: 42777
15 23:37:36 saveConfig . . . EEPROM OK Len: 250 Crc: 1478
15 23:37:42 saveConfig . . . EEPROM OK Len: 247 Crc: 22920
15 23:37:47 saveConfig . . . EEPROM OK Len: 245 Crc: 33531
15 23:37:55 saveConfig . . . EEPROM OK Len: 247 Crc: 11595
15 23:38:01 saveConfig . . . EEPROM OK Len: 248 Crc: 31221
15 23:38:15 saveConfig . . . EEPROM OK Len: 247 Crc: 53814
15 23:38:19 Relay 1 . . . ON
15 23:38:20 Relay 1 . . . OFF
15 23:38:24 saveConfig . . . EEPROM OK Len: 248 Crc: 22860
15 23:38:27 Relay 1 . . . ON
15 23:38:28 Relay 1 . . . OFF
15 23:38:35 saveConfig . . . EEPROM OK Len: 250 Crc: 39221
15 23:38:39 saveConfig . . . EEPROM OK Len: 247 Crc: 22920
15 23:38:42 saveConfig . . . EEPROM OK Len: 250 Crc: 1478
15 23:38:45 saveConfig . . . EEPROM OK Len: 250 Crc: 42777
15 23:38:52 Relay 1 . . . ON
15 23:38:53 Relay 1 . . . OFF
15 23:39:03 Update:
15 23:39:03 Update Error[10]: Magic byte is wrong, not 0xE9
15 23:39:24 saveConfig . . . EEPROM OK Len: 171 Crc: 179
15 23:39:25 The current version is already the latest version
15 23:41:15 Relay 1 . . . ON
15 23:41:25 saveConfig . . . EEPROM OK Len: 171 Crc: 19085
15 23:46:51 Relay 1 . . . OFF
15 23:47:01 saveConfig . . . EEPROM OK Len: 171 Crc: 179
No neutral wire connected? If there is no neutral wire, a capacitor must be installed. If the power of your LED light is less than 5W, it will also cause flickering.